Auxiliary Engines:

Cat C32 Auxiliary / Diesel Electric Propulsion Engine (IMO III)

Cat C32 Auxiliary / Diesel Electric Propulsion Engine (IMO III)
Minimum Rating
1047 BHP
Maximum Rating
1332 BHP
Aspiration
Turbocharged-aftercooled
Bore
5.71 in


Product Specs

  • Power Rating

  • Minimum Rating
    1047BHP
    Maximum Rating
    1332BHP
  • Engine Specifications

  • Aspiration
    Turbocharged-aftercooled
    Bore
    5.71in
    Configuration
    Vee 12, 4-stroke-cycle diesel
    Displacement
    1959in³
    Rotation
    Counterclockwise from flywheel end
    Stroke
    6.38in
    Emissions
    IMO III emissions certified (SCR required)
    Cooling
    Heat exchanger or keel cooled
    Flywheel Housing
    SAE No. 0 with SAE No. 18 flywheel (136 teeth)
    Governor
    Electronic (A5 ECM)
    Oil Change Interval
    750 hrs - deep pan
    Rated Engine Speed
    1500 rpm
    Refill Capacity
    Lube Oil System w/ oil filter change: 146 L (38.5 gal) - deep pan
  • Dimensions & Weights

  • Maximum Engine Dry Weight
    7160lb
    Maximum Height
    63.5in
    Maximum Length
    89.8in
    Maximum Width
    57.3in
    Minimum Engine Dry Weight
    6950lb
    Minimum Height
    59.3in
    Minimum Length
    83.9in
    Minimum Width
    57.1in
  • Clean Emissions Module (CEM) - Dimensions

  • 6 Brick U-Flow - Height
    23.5in
    6 Brick U-Flow - Length
    85in
    6 Brick U-Flow - Weight
    1235lb
    6 Brick U-Flow - Width
    56.9in
    6 Brick Z-Flow - Height
    23.5in
    6 Brick Z-Flow - Length
    147.7in
    6 Brick Z-Flow - Weight
    1246lb
    6 Brick Z-Flow - Width
    43.5in
    Dosing Cabinet - Height
    22.8in
    Dosing Cabinet - Length
    37.4in
    Dosing Cabinet - Weight
    209lb
    Dosing Cabinet - Width
    18.8in

Equipment

  • Air Inlet System
    • Separate circuit aftercooled (SCAC)
    • Closed crankcase fumes disposal
  • Control System
    • 24V control system
  • Cooling System
    • Heat exchanger or Keel Cooling
    • Watercooled exhaust manifold and turbocharger
    • Hard seawater lines – no flexible hoses
    • Flanges for cooling connections, ANSI or DIN
  • Fuel System
    • Duplex fuel filters with hybrid fuel lines
    • Shipped loose primary fuel filter with water separator
    • Fuel transfer and priming pump
  • Lube System
    • Oil fill, simplex filter and dipstick
    • Deep or shallow sump oil pan
  • Mounting System
    • Adjustable front support mounting system
  • General
    • Right or left hand service sides
    • Customer wiring and service tool connector
  • Alarm And Protection
    • MECP I control panel
    • MECP III control panel with Cat® Alarm and Protection System
  • Exhaust System
    • Water-in-fuel and exhaust temperature sensors
    • Muffler
  • Charging System
    • Charging alternator
  • Fuel System
    • Manual or electric fuel priming pump
    • Fuel cooler
  • Lube System
    • Duplex oil filters
  • Power Take-offs
    • Front drives including stub shaft and pump drive
    • Rear SAE A or B pump drives
  • Starting System
    • Starting motors – air, electric or redundant

Request a Quote

Find a Boyd CAT
Location or Rep Near You

BOYD CAT USED PARTS - offering discontinued, rebuilds, out of stock, and CAT bargain list and aftermarket. Save money. Buy used. Used_Parts@BoydCAT.com

X