Oil and Gas:

C13 ACERT™ Dry Manifold Petroleum Engine

C13 ACERT™ Dry Manifold Engine
Length
47.3 in.
Width
39.9 in.
Height
46.7 in.
Weight
1976.0 lb

Cat C13 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C13 ACERT engines to deliver excellent performance with low operating costs and emissions. Equipment powered by C13 ACERT engines include workover rigs, pump skids, acidizing units, cementing units, blenders, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. Cat C13 ACERT™ Industrial Diesel Engine. Ratings: 287-388 bkW (385-520 bhp) @ 1800-2100 rpm meet China Stage II, U.S. EPA Tier 3 equivalent or U.S. EPA Tier 2 equivalent, EU Stage IIIA equivalent or EU Stage II equivalent emission standards.



Product Specs

  • Dimensions

  • Length
    47.3in.
    Width
    39.9in.
    Height
    46.7in.
    Weight
    1976.0lb
    Length
    47.3in
    Width
    39.9in
    Height
    46.7in
    Weight
    1976lb
  • Capacity for Liquids

  • Lube Oil System (refill)
    9.0gal
    Lube Oil System - Refill
    9gal (US)
    Cooling System
    3.8gal (US)
  • General Specifications

  • Minimum Rating
    385BHP
    Maximum Rating
    520BHP
    Governor and Protection
    Electronic (ADEM™ A3)
    RPM
    2100r/min
    Aspiration
    Turbocharged-Aftercooled
    Displacement
    760in³
    Flywheel and Flywheel Housing
    SAE 1
    Flywheel Teeth
    113
    Rotation from Flywheel End
    Counterclockwise
    Stroke
    6.2in
    Bore
    5.1in
  • Emissions

  • Emissions
    EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA

Equipment

  • Air Inlet System
    • Turbocharger, mid-mounted
    • Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection
  • Control System
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Power compensation for fuel temperature
    • Programmable low and high idle and TEL
    • Electronic diagnostics and fault logging
    • Engine monitoring system — speed, temperature, pressure
    • J1939 Broadcast — diagnostic and engine status
  • Cooling System
    • Thermostats and housing
    • Jacket water pump — gear-driven
    • Front water pump inlet
  • Exhaust System
    • Exhaust manifold — dry
    • Front turbo exhaust
  • Flywheels And Flywheel Housings
    • See Mandatory Options
  • Fuel System
    • Electronic unit injector
    • Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
    • Fuel transfer pump — front
    • Fuel priming pump — LH mid-mount
    • Fuel fitting — fuel return connection: straight No. 8, 5/8-18
  • Lube System
    • Crankcase breather
    • Oil cooler
    • Oil filter — RH
    • Oil pan — front sump, 40 L capacity
    • Oil filler — LH front
    • Oil dipstick — LH front
    • Oil pump
    • Oil valve sampling — RH rear engine side
  • Power Take-offs
    • Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
    • Hydraulic pump drive — SAE A, 11-tooth
    • 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)
  • General
    • Vibration damper
    • Paint — Cat yellow
    • Lifting eyes
    • Automatic variable timing, electronic
    • Electronic installation kit (connectors, pins, sockets)
    • Literature
  • Mandatory Options
    • Flywheel housing or rear PTO
    • Throttle position sensor
    • Primary filter/water separator
  • Air Compressor
    • Air compressors
    • Air chambers
    • Air compressor governors
  • Air Inlet System
    • Air cleaners
    • Precleaners
    • Air lines
    • Air inlet gasket
  • Belt-driven Accessories
    • Refrigerant compressor and mounting
  • Charging System
    • Charging alternators
    • Alternator mountings
    • Alternator guard
    • Alternator accessories
  • Control System
    • Connection
  • Cooling System
    • Radiator — installed
    • Fan drive f/u/w Caterpillar installed radiator
    • Fan drive pulleys f/u/w customer-supplied radiators
    • Coolant conditioner
    • Water lines — pump inlet
    • Fan drive mountings
    • Fan height instructions
    • Fan adapters for suction fans and blower fans
    • Suction fans and blower fans
    • Coolant level sensor
    • Aftercooler lines
  • Exhaust System
    • Muffler
    • Flexible fitting
    • Elbows, flange, pipe, clamp
    • Straight exhaust adapter
  • Fuel System
    • Fuel lines for fuel filter
    • Fuel cooler
    • Fuel fitting — fuel return connection
    • Flexible fuel lines
  • Instrumentation
    • Gauges and instrument panels
    • Voltmeters
    • Gauge mounting
    • Ammeter
  • Lube System
    • Oil pan
    • Oil pan drain
    • Oil level gauges
    • Oil filter — bypass and remote
    • Lubricating oil
    • Oil filler
    • Fumes disposal
  • Mounting System
    • Front and rear engine supports
    • Structural steel base
  • Power Take-offs
    • Crankshaft pulleys
    • Crankshaft pulley — stack-on
    • Output flange
    • Flywheel stub shaft
    • Front stub shaft
    • Hydraulic pump drive
    • Hydraulic pumps — front and rear
    • Enclosed clutch
    • Clutch support
  • Protection System
    • Air shutoff
    • Air shutoff switch
  • Starting System
    • Starting System
    • Starting aids
    • Battery sets — 24 Volt, dry
    • Battery cable
    • Battery rack
  • Transmission Arrangement
    • Transmission cooler

Request a Quote

Find a Boyd CAT
Location or Rep Near You

BOYD CAT USED PARTS - offering discontinued, rebuilds, out of stock, and CAT bargain list and aftermarket. Save money. Buy used. Used_Parts@BoydCAT.com

X