Auxiliary Engines:

Cat C32 Auxiliary/Generator Set Engine (EPA Tier 3)

C32 Tier 3
Minimum Rating
1047.0 bhp
Aspiration
TTA
Configuration
Vee 12, 4-Stroke-Cycle Diesel
Bore
5.7 in

C32 ACERT auxiliary/generator set engines incorporate a separate circuit aftercooling system (SCAC) for all configurations. The primary advantage of the SCAC systsem is reduced aftercooler corrosion since no sea water circulates through the aftercooler. Many other improvements on these engines also contribute to minimizing owning and operating costs. The EPA Tier 3, IMO II, EU Stage IIIA compliant ratings are available with heat exchanger or keel cooled options. Heat exchanger configurations have an optional front mounted sea water pump.



Product Specs

  • Power Rating

  • Minimum Rating
    1047.0bhp
    Maximum Rating
    1333BHP
    Minimum Rating
    1047BHP
  • Engine Specifications

  • Aspiration
    TTA
    Configuration
    Vee 12, 4-Stroke-Cycle Diesel
    Bore
    5.7in
    Stroke
    6.4in
    Displacement
    1959.0in3
    Rotation (from flywheel end)
    Counterclockwise
    Aspiration
    TTA
    Bore
    5.7in
    Configuration
    Vee 12, 4-Stroke-Cycle Diesel
    Displacement
    1959in³
    Rotation from Flywheel End
    Counterclockwise
    Stroke
    6.4in
  • Dimensions & Weights

  • Minimum Length
    83.5in
    Maximum Length
    89.9in
    Minimum Width
    60.2in
    Maximum Width
    60.2in
    Minimum Height
    60.9in
    Maximum Height
    62.5in
    Minimum Dry Weight
    6950.0lb
    Maximum Dry Weight
    7160.0lb
    Maximum Dry Weight
    7160lb
    Maximum Height
    62.5in
    Maximum Length
    89.9in
    Maximum Width
    60.2in
    Minimum Dry Weight
    6950lb
    Minimum Height
    60.9in
    Minimum Length
    83.5in
    Minimum Width
    60.2in

Equipment

  • Air Inlet System
    • Separate circuit after-cooled (SCAC)
    • Air cleaner
    • Turbocharger, jacket water cooled
    • Turbocharger inlet, 152 mm (6 in) OD straight connection
  • Control System
    • Programmable Low Idle (550 - 750 rpm)
    • Programmable High Idle Limit for WOSR Ratings
    • Electronic diagnostics and fault logging
    • Engine and transmission monitoring (speed, temperature, pressure)
    • Electronic fuel/air ratio control
    • Engine Protection Mode for extended ambient conditions
    • 70-pin customer connector
    • Throttle Input signal options
    • 0 - 5 Volts
    • 4 - 20 mA
    • PWM (Pulse Width Modulated)
  • Cooling System
    • Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
    • Jacket Water (JW) and SCAC Heat Exchangers Shell & Tube for HEX cooled engines
    • SCAC pump, gear driven
    • Jacket water pump, gear driven
    • Sea water pump, bronze impeller, gear driven, when selected for Hex cooled engines
    • Sea water Pump & JW Heat Exchanger Connection: 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange Connection
    • Keel Connections: 76.2 mm (3in) ID Standard 4 Bolt
    • SCAC and JW shunt tanks for maintaining proper pump inlet pressures
  • Exhaust System
    • Water-cooled exhaust manifold & turbocharger
    • 4 Bolt 130 mm (5.12 in) diameter flanged outlet
  • Flywheels & Flywheel Housings
    • SAE standard rotation (CCW facing exciter end)
    • Flywheel Housing: SAE No. 0, Flywheel: 18 inch, 136 teeth
  • Fuel System
    • Duplex Fuel Filters, Spin-on, RH & LH service
    • Fuel connections size: r driven
    • Plate-type fuel cooler installed behind Aftercooler Shunt Tank
    • Fuel transfer pump, gear driven
    • Manual fuel priming pump
    • Hybrid fuel line design
  • Lube System
    • Simplex Oil Filters, RH or LH service
    • Deep sump oil pan
    • RH or LH service oil filler locations
    • RH or LH service dipstick
    • Oil pump, gear driven
  • Mounting System
    • Front support - 33 inches wide
  • Power Take-offs
    • Front Poly-V groove pulley (Quantity 1) for auxiliary drives
  • General
    • Common electrical bonding point
    • Engine does not ship with zinc components
  • Exhaust System
    • Dry Elbows
    • Flexible Fitting
    • Flange
    • Muffler
    • Muffler Spark Arresting
  • Air Inlet System
    • Air Inlet Adapter
  • Charging System
    • Battery Chargers
    • Charging Alternators
    • Ammeter
  • Control System
    • Load Sharing Attachment
    • Instrument Panels
    • Caterpillar Alarm Protection
    • Fuel and Oil Shielding
  • Fuel System
    • Water Separator
  • General
    • FUMES DISPOSAL SYSTEM
  • Instrumentation
    • Instrument Panels
    • OEM Wiring Harness
    • Engine to Engine Harness
    • Gauges
    • Transmission Sensors
    • Exhaust Temperature Sensors
  • Lube System
    • Duplex Oil Filters
    • Sump Pump
  • Power Take-offs
    • Rear Hydraulic Pump Drive
  • Starting System
    • Electric Starting Motors - Single 24 Volt
    • Air Starting Motor
    • Dual Starting Motors (Electric and Air)
    • Air Start Accessories
    • Starting Aids - JW Heaters
    • Battery Sets - 24 Volt - Dry
  • Mounting System
    • Front Support
    • Rear Support
    • Isolators Mounts
    • Adapter Kits
  • Packing
    • Engine Protective Cover
    • Storage Preservation
    • Export Packing

Request a Quote

Find a Boyd CAT
Location or Rep Near You

BOYD CAT USED PARTS - offering discontinued, rebuilds, out of stock, and CAT bargain list and aftermarket. Save money. Buy used. Used_Parts@BoydCAT.com

X